Fiber Optic Services in Arizona

Allow your Arizona-based business to take advantage of fiber optic systems.

AZ CCTV and SECURITY can upgrade your current network or even complete brand-new cable installations. Fiber optic has numerous benefits, such as improved data transmission capability, consistent communication, sturdy wiring, higher speed, and immense potential for upgrade integration with newer technologies.


We handle the cable termination in two ways. We could create a temporary joint by using connectors that can make the two fibers and/or the fiber can be connected to a piece of network gear. Alternatively, splices can be used to create a permanent joint. The right style of terminations must be used, and the installation process must be conducive to damage prevention and dirt protection, as well as minimal loss.

Termination gets more attention than any other fiber optic area. This is the reason that manufacturers have created more than 80 connector styles and more than a dozen installation methods. Splices fall under two major categories, but they can be implemented in many ways. Fortunately for both you and us, most applications only use a few. Single-mode and multi-mode connectors require different splice termination procedures and different connectors. Therefore, you should never specify splices or connectors before knowing what fiber is going to be used.


Testing is a measure that helps to gauge fiber optic component performance, systems, and cable plants. The process ensures that performance specifications are confirmed, and it also makes it clearer to see how components, such as receivers, detectors, splices, connectors, fiber, and laser sources, work together. This happens while the said components are being developed.


How long does fiber fusion splicing take?

Fusion splicing is an excellent idea for both the fibers and any Arizona location where a number between 48 and 192 fibers need to be spliced

Either two fiber technicians or one technician plus an assistant per joint

  • 72-fiber cable size
  • Two-and-a-half-hour preparation time
  • Six-hour splice and coil time
  • Eight-and-a-half-hour total
  • 144-fiber cable size


Recently, it’s become evident that copper wire is no longer the best means of transmission for a communication signal. This realization is the reason that fiber optics are slowly replacing these copper wires. Not only do fiber optics form the backbone of numerous network systems, but they also bridge the long-distance gap between various phone systems. There are other system users, such as electric utility companies, office buildings, industrial plants, cable television services, and university campuses.

Fiber optics are very similar to the copper wire system that is being phased out. The difference lies in the way that information is transmitted. Fiber optics employ light pulses for information transmission down fiber lines. Copper wires, on the other hand, use electronic pulses, which are responsible for information transmission down copper lines. If you look at the various components in a fiber-optic chain, you can better understand the way that the system works in tandem with wire-based systems.

There lies a transmitter at the end of one system. Any information that is coming onto the fiber optic lines has this as a point of origin. The copper wire’s coded electronic pulses are accepted by the transmitter. Next, the said information is both processed and translated to coded light pulses that are equivalent. Either an Injection-laser Diode (ILD) or a Light-emitting Diode (LED) may be used for light pulse generation. Before light pulses travel down the cable, a lens is used to funnel them through the fiber optic medium. The near-infrared light is typically 850nm for the shortest of distances and 1,300nm for the longer distances for multi-mode fiber. These figures become 1,300 nm for short distances and 1,500 nm for longer distances on single-mode fiber. Think of the roll in a paper towel. A fiber cable is akin to a more extended version of this with a mirror coating inside.

Should you shine a flashlight from an end, you should see it from the other, even if there is a bend in the fiber. Thanks to total internal reflection, the light pulses travel down the line effortlessly. The principle focuses on the angle of incidence. If it’s more than a critical value, light is prevented from escaping the glass, so it just bounces inward. When you apply this to fiber-optic strand constriction, you can better understand the light pulse transmission.

Note that the core must be a pure material that is clear. Plastic is acceptable if the distance is very short, but glass is the standard. While pure silica is typical of glass optical fibers, chalcogenide, fluoroaluminate, and fluorozirconate glasses may be used for infrared applications with longer wavelengths.

Protect What’s Important. Your Family, Business & Property. We Can Help.